Jump to content
Notice to Hotmail/Gmail & BT Internet users - Please check your SPAM/JUNK folders for our emails. Please add our email as a contact to your email account.
Sign in to follow this  
Todger182

Lupo/Polo Clock Wiring Pinout

Recommended Posts

Todger182

As title suggests, I'm after the pin out for a lupo 1L E pre canbus, but I'm sure a pre canbus polo 1.4 with the round clocks will be the same.

I'm sure somebody has done it or can point me in the right direction to another thread somewhere.

Thanks

Share this post


Link to post
Share on other sites
nige8021

32-pin connection (vehicle identification no. 6X)

1 -Terminal 15, positive

2 -Right turn signal warning lamp

3 -E. speedometer output

4 -Not assigned

5 -Fuel gauge sender

6 -Airbag

7 -Sensor earth, terminal 31

8 -Coolant temperature sender

9 -Terminal 31, earth

10 -Oil pressure switch, high

11 -Speed signal

12 -Alternator warning lamp, terminal 61

13 -Glow period warning lamp or catalytic converter monitor warning lamp → Note

14 -Rear fog light warning lamp

15 -Not assigned

16 -Not assigned

17 -Main beam warning lamp, terminal 56a

18 -Left turn signal warning lamp

19 -Anti-lock brake system (ABS)

20 -Dash panel insert illumination, terminal 58d

21 -Driver door open signal

22 -Coolant shortage indicator

23 -Terminal 30, positive

24 -Terminal 31, earth

25 -Self-diagnosis, K wire

26 -Right parking light

27 -Left parking light

28 -E. speedometer input

29 -Brakes general

30 -S-contact

31 -Seat belt

32 -Side light warning lamp or exhaust emissions warning lamp → Note

1) Is assigned depending on engine fitted or specific country equipment

Share this post


Link to post
Share on other sites
Todger182

That's the pinout for a canbus polo/lupo so no good to me. Cheers anyway.

 

Thanks

 

X

Share this post


Link to post
Share on other sites
nige8021
17 minutes ago, Todger182 said:

That's the pinout for a canbus polo/lupo so no good to me. Cheers anyway.

 

Thanks

 

X

No it's not the CAN-Bus ones are the 6E designation and the CAN-Bus is on the other 32 pin connector 

 

32-pin connection, green (vehicle identification no. 6E)

5 -EPS (electromechanical power steering) → Note

15 -EPC → Note

19 -CAN high

20 -CAN low

25 -Reset

26 -Ambient temperature → Note

27 -CAN high external

28 -CAN low external

 

32-pin connection, blue (vehicle identification no. 6E)

1 -Terminal 15, positive

2 -Right turn signal warning lamp

3 -E. speedometer output

4 -Not assigned

5 -Fuel gauge sender

6 -Airbag

7 -Sensor earth, terminal 31

8 -Coolant temperature sender

9 -Terminal 31, earth

10 -Oil pressure switch, high

11 -Speed signal

12 -Alternator warning lamp, terminal 61

13 -Glow period warning lamp or catalytic converter monitor warning lamp → Note

14 -Rear fog light warning lamp

15 -Not assigned

16 -Rear lid

17 -Main beam warning lamp, terminal 56a

18 -Left turn signal warning lamp

19 -Anti-lock brake system (ABS)

20 -Dash panel insert illumination, terminal 58d

21 -Driver door open signal

22 -Coolant shortage indicator

23 -Terminal 30, clock

24 -Terminal 31, earth

25 -Self-diagnosis, K wire

26 -Right parking light

27 -Left parking light

28 -E. speedometer input

29 -Brakes general

30 -S-contact

31 -Seat belt

Share this post


Link to post
Share on other sites
Todger182
23 minutes ago, nige8021 said:

No it's not the CAN-Bus ones are the 6E designation and the CAN-Bus is on the other 32 pin connector 

 

32-pin connection, green (vehicle identification no. 6E)

5 -EPS (electromechanical power steering) → Note

15 -EPC → Note

19 -CAN high

20 -CAN low

25 -Reset

26 -Ambient temperature → Note

27 -CAN high external

28 -CAN low external

 

32-pin connection, blue (vehicle identification no. 6E)

1 -Terminal 15, positive

2 -Right turn signal warning lamp

3 -E. speedometer output

4 -Not assigned

5 -Fuel gauge sender

6 -Airbag

7 -Sensor earth, terminal 31

8 -Coolant temperature sender

9 -Terminal 31, earth

10 -Oil pressure switch, high

11 -Speed signal

12 -Alternator warning lamp, terminal 61

13 -Glow period warning lamp or catalytic converter monitor warning lamp → Note

14 -Rear fog light warning lamp

15 -Not assigned

16 -Rear lid

17 -Main beam warning lamp, terminal 56a

18 -Left turn signal warning lamp

19 -Anti-lock brake system (ABS)

20 -Dash panel insert illumination, terminal 58d

21 -Driver door open signal

22 -Coolant shortage indicator

23 -Terminal 30, clock

24 -Terminal 31, earth

25 -Self-diagnosis, K wire

26 -Right parking light

27 -Left parking light

28 -E. speedometer input

29 -Brakes general

30 -S-contact

31 -Seat belt

I'm trying to swap GTI clocks in, and it's lighting up like a christmas tree. oil pressure buzzer and light on even though it's fine. no speedo, and no rev counter. I have both green and blue plugs in my clocks but my green plug has 3  only wires.

 

My blue plug is obviously missing a few as well. Looking like I need to get the mulitmeter out.

 

Thanks

 

X

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. Terms of Use Privacy Policy Guidelines