Skip to content

How many smooth 16v front bumpers crack?

Featured Replies

How many of you guys have had yours cracked? I won a 16v bumper for £1.20 on eBay (epic) , i want to smooth it but I'm concerned it will crack? Whats the best way of going about it? And is plastic filler worth getting instead of normal filler?

I was thinking attempted to plastic weld a panel in each gap with a soldering iron, P40 behind it to reinforce the plastic weld, then skin over in plastic filler?

  • Replies 16
  • Views 2.4k
  • Created
  • Last Reply

Top Posters In This Topic

done mine years ago and still hasnt cracked. plastic weld ftw

done mine years ago and still hasnt cracked. plastic weld ftw

Wicked, did you do anything to reinforce it or just weld it? Did you chop the recess out (like the bit that goes in to where the grill clips in) or just plate over it? Did you use plastic filler too or normal P38? Thanks mate :)

they only really crack if they have been bodged, plastic welding is the way to go really mate

I won a 16v bumper for £1.20 on eBay (epic)

God damn it! Wish I had known there was one on :disgust: well done on that though.

Will admit - this is good information for when I get some (i hope) :lol:

I won a 16v bumper for £1.20 on eBay (epic)

You've been ripped off :lol:

My smoothed bumper was fine when I had it.

Sold the car to my mate, its now cracked, pretty much due to him driving like a knob.

Mine didnt even crack after being fucked by a massive coach, plastic weld indeed :-)

And lots of it on the underside, where the plate joins. Then fiberglass on top, and finally skim of filler to smooth

At 1.20 does it matter if it cracks? You could repair it and it will still be cheaper than some of the faggots at scrappys charge.

I won a 16v bumper for £1.20 on eBay (epic)

God damn it! Wish I had known there was one on :disgust: well done on that though.

Will admit - this is good information for when I get some (i hope) :lol:

I won a 16v bumper for £1.20 on eBay (epic)

You've been ripped off :lol:

My smoothed bumper was fine when I had it.

Sold the car to my mate, its now cracked, pretty much due to him driving like a knob.

Ah well i drive mine carefully as it owes me too much haha!

Mine didnt even crack after being fucked by a massive coach, plastic weld indeed :-)

And lots of it on the underside, where the plate joins. Then fiberglass on top, and finally skim of filler to smooth

they only really crack if they have been bodged, plastic welding is the way to go really mate

At 1.20 does it matter if it cracks? You could repair it and it will still be cheaper than some of the faggots at scrappys charge.

Alright cool, thanks guys, seem's i need to get some plastic then :D Don't suppose anyone has any pictures or a guide just so i can read through it anyway?

I just cut plates from the old 8v bumper, to get similar curves. Then cut rods off to use to 'weld' together

Recyling, saves the world :lol:

Epic! Idea stolen :)

Done mine the other day, havnt completely finished it yet tho. heres what i done.

Step 1 - cut the hole (i used an angle grinder)

picture087f.th.jpg

Step 2 - using an old 8v rear bumper cut a peice out of similiar size, i cut this slightly bigger so i could allign the shape of the bumper correctly and trim down accordingly.

picture088hk.th.jpg

step 3 - begin plastic welding, to start with i jus ran the soldering iron across the joins leaving an indent in the plastic which i then filled using the offcuts of plastic from trimming. also did this on the reverse side.

picture091n.th.jpg

Step 4 - sand down the joins to create a level surface and use a skim of filler over the top where needed. (i havnt finished this yet)

This is just what i have done, it may not be the correct way to some of you so dont slate me for it :D sorry about the pics being the wrong way imageshack is being strange.

Hope this helps.

Dale.

Edited by Dexy_

thats how i did mine before a jumped on my bumper in rage!!!lol looks well dude i made the mistake of cutting the 8v bumper too short! :biggrin:

thats how i did mine before a jumped on my bumper in rage!!!lol looks well dude i made the mistake of cutting the 8v bumper too short! :biggrin:

Cheers mate, yee i left plenty of room for it to be trimmed down lol.

Wicked idea there with the 8v rear bumper to fill that gap! I know what to do now, cheers :D Does the line in the rear bumper follow the line of the front one then?

You just wanna plastic weld in a way that you have to use a minimal amount of filler. That way the chance of it cracking is much smaller.

Create an account or sign in to comment

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.