Skip to content

Mk2 Lights of a Mk3 Polo...

Featured Replies

I'm starting a new project soon, i love the round headlights on mk2's the twin type but i dont like the back lights and small bumpers, dash ect.

Soooo, how hard is it to put the mk2 lights on a mk3? Guessing you need mk2 bonnet, wings, lights, grille?

Anything else? Any welding / fabrication needed?

Cheers.

Ash

  • Replies 11
  • Views 2.7k
  • Created
  • Last Reply

Top Posters In This Topic

Posted Images

  • Author

Forum seems quiet today....

Bump

I think the front panel on a mk2 is welded on, but you can rivet it. This is just stuff I've read. Don't know the answer 100% but your guess seems correct! Definitely what you've listed so far maybe the panel and valance but I'm not 100% on this...

you would need alot of work to carry this out as theres alot of panel difference on a mk3s front when compared to a mk2 not to mention a mk3 has chassis extentions

you would need the following items

bonnet

wings

slam panel

lower valence

scuttle under windscreen

front cross member

probably more but cant remember of the top off my head.there would be alot of welding and you would have to remove the chassis extensions.

it would be far easier to start with a mk2 and customise a mk3 front bumper to fit and fit a mk3 rear panel and bootlid to get the mk3 rear lights

luke

The scuttle panel is the same,still has the earlier bonnet lines in it,but the base of the A-pillars taper in on the later car,so the wings can cross them. The facelift lengthened the car,with said extensions on the legs (easy to sort) and different front panel,slam panel and cross member design (not so easy). Alot of work.

  • Author

Iv been thinking about this somemore, the back lights look like they will fit without too much effort.

Obivously would need to change the boot for a mk3 one, would this fit straight on?

post-8715-1208975287.gif

The bit annotated, would this be need to be replaced and tack welded because of the wider lights?

Thanks

the rear panel is different so you would neet to change that for a mk3 one then obviously tailgate lights etc easier to do than the front end swap but will still need welding doing

luke

  • Author

how do you mean rear panel? the bit of noted?

Think i can manage to weld that.

This is possible, and it'd be easier to swap the back end than the front. Even the A-pillars are different up front - on a Mk3 the wings cut into the A pillars, on a Mk2 they don't.

The problem is, if you weld a Mk3 rear slam panel onto your Mk2 you'll still have to bodge a Mk3 bumper on the front. The Mk3 front end is longer, and the slam panel doesn't extend as far as the bottom of the car. On a Mk2 the slam panel is the whole front end. Making the bumper fit properly isn't easy to do properly.

I've seen a Mk3 with a Mk2 front end. This was years ago, hence the bloody lousy pictures.

2-3-1.jpg

2-3-2.jpg

The weird thing was, the front end conversion had been done really well. The factory fit pinstripe had been extended down the Mk2 wings, it was well painted and the Mk2 spec A-pillars looked factory too. But other than the front end conversion it was completely standard and quite tatty, and looked to be based on a pov spec Mk3 Polo. That and the front bumper was really badly swapped.

Which begs the question, why did someone do all the hard work properly, then fluff the front bumper? And, more interesting, why do all this to an otherwise fairly tatty pov Mk3 Polo and not bother with any other mods. Very odd.

If you want a Mk3 rear end, you'll have to weld in the entire panel. I believe this goes from just above the rear lights down to the bottom of the car.

Edited by Alex

  • Author
This is possible, and it'd be easier to swap the back end than the front. Even the A-pillars are different up front - on a Mk3 the wings cut into the A pillars, on a Mk2 they don't.

The problem is, if you weld a Mk3 rear slam panel onto your Mk2 you'll still have to bodge a Mk3 bumper on the front. The Mk3 front end is longer, and the slam panel doesn't extend as far as the bottom of the car. On a Mk2 the slam panel is the whole front end. Making the bumper fit properly isn't easy to do properly.

I've seen a Mk3 with a Mk2 front end. This was years ago, hence the bloody lousy pictures.

2-3-1.jpg

2-3-2.jpg

The weird thing was, the front end conversion had been done really well. The factory fit pinstripe had been extended down the Mk2 wings, it was well painted and the Mk2 spec A-pillars looked factory too. But other than the front end conversion it was completely standard and quite tatty, and looked to be based on a pov spec Mk3 Polo. That and the front bumper was really badly swapped.

Which begs the question, why did someone do all the hard work properly, then fluff the front bumper? And, more interesting, why do all this to an otherwise fairly tatty pov Mk3 Polo and not bother with any other mods. Very odd.

If you want a Mk3 rear end, you'll have to weld in the entire panel. I believe this goes from just above the rear lights down to the bottom of the car.

Lol that is pretty random.

http://www.clubpolo.co.uk/forum/index.php?showtopic=85518

Looks quite well done there, I'm actually not overly bothered about the bumper issue! its just something about the boot and lights i cant stand on the mk2 but i just love the front with the single light debadged grille.

Plus the car is lighter.

Think I'm going to go to the scrap yard and try and work out what needs doing...

The car is lighter because of other weighty things the later version got,such as side impact bars etc. I think your best bet would be modifying a later car,as you can leave the A pillars as they are. But the front panelwork will all have to be welded in properly.

Interesting pics Alex, not seen it done.

Create an account or sign in to comment

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.