hi all,

i have a spare set of bumpers which i am probably not going to use so up for sale they go !

front and back bumpers, both in primer. the rear had a few scrapes which where filled and flatted but now has more storage marks so will need going over again. all the tabs are intact etc only notable hing is the lower edge has melted slightly where the exhaust had hit it i think, but this is the inner edge and isnt visible when ftted unles of course your laying down with your head under it, but if you are then the melted plastic is the least of your worries :)

£45 collected £55 posted

front bumper had a crack and had an attempted repair by a friend who "knew what hes doing" obviously not a good one because the filler has flaked away. its a clean crack so should be easy enough to repair. seems pretty common for them to crack in this area. i think i might have some spare grilles somewhere, but they will be included if i find them as a free extra so the bumper is sold as is. the towing eye cover is missing, my plan was to smooth it over but didnt get that far. fogl ights are not included. the two grilles are included

£55 collected £65 posted

the splitter is in reasonable condition, might have the odd mark etc but fits well and is already cut to fit the 16v bumper and looks pretty smart in my opinion. plan was to fill in any scratches and then paint it in textured bumper paint. this will go back on a 6n2 but will need screwing down as the tabs arent there anymore. - just checked the pictures and it has a burn mark where a crack was plastic welded, so will need a bit of atention.

£35 collected £40 posted

I'm located on the kent / sussex boarder in a town called lydd tn29 postcode, i also travel to bedfordshire pretty much once a week, so east london or essex etc i can drop off if not too far off my route.

postage will be by Yodel 48 hour courier so is tracked etc.

pics to follow

Edited 29 September, 201411 yr by dixy

Have you any pics of splitter please I'm sort of local to you so will collect

hi buddy, pics added.

i dont mind meeting somewhere if its easier for you, say ashford so easy from m20 etc.let me know

Ok I'm from ashford anyway. When you say its been cut will this be noticeable on the 6n2 bumper. Cheers

hi,

no it wont be visible at all, basically its the little locating fingers / tabs that have been cut off because they dont line up with the 6n bumper.

I'm going up north tomorrow morning and will be passing ashford, may be coming back tomorrow night (late) or wednesday morning. let me know if your around and I'm happy to drop it by.

I'm not about I'm afraid till thursday/friday

If he's cut all the tabs off it will not fit your 6n2 without glueing or bodging it on as the tabs are all that holds it on to the 6n2 bumper

Oh bugger

Would you sell the right side grill from the front bumper

it will deffinatly fit back on a 6n2, i have on that was cut in the same way and it only need 4 small screws to hold it on. could use 2 really but 4 is better. i used 2 at each end through the throught the edge of the bumper. imo its stronger then the clips and definably wont fall off.

welcome to come and check it out before hand etc.

smg4life, which grille do you mean? i only have the ones in the pictures right now, and they are the near side upper and lower (which is the fog light type) i may have a right side somewhere but will have to dig it out. again depends which one your after :)

OPEN TO OFFERS GUYS and I'm happy to post to you

thanks

Offers anyone?

Now on eBay,

http://www.ebay.co.uk/itm/201192542965?ru=http%3A%2F%2Fwww.ebay.co.uk%2Fsch%2Fi.html%3F_from%3DR40%26_sacat%3D0%26_nkw%3D201192542965%26_rdc%3D1

Need these gone guys, make me an offer