Jump to content
Sign in to follow this  
kiran_182

Black polo gt coupe

Recommended Posts

kiran_182

Got a polo gt coupe in black, really condition bar the hole in the driver sill / floorpan and the 2 inch one in the passenger sill. Interior is almost mint, driver seat has an open seem on top corner.

 

Pretty much std with a single wiper conversion, home brew mount 

 

Not had it to long so not given it a full going over, did notice the rad is cracked and the member it sits on is bent so its tapped an curb?

 

Waiting on photobucket to show my pics

 

Really would be nice for it to go whole as its a hardtop gt in black and pretty good condition 

 

VW-Polo-GT-For-spares-or-repairs_zpsn6xq

 

Edited by kiran_182

Share this post


Link to post
Share on other sites
Elijah

Mileage? History?

 

its a rare polo gt as not many h plates about especially in black.

 

most were red or white.

Share this post


Link to post
Share on other sites
kiran_182

Its on 120k ish, no history with it

 

This is the hole in the driver sill/ floor pan. The bottom of the box of the sill is gone 

 

20180522_142250_zpsrsemtcfl.jpg

 

Would sell it whole if somone wants is,  rest of the car is in good order

Edited by kiran_182

Share this post


Link to post
Share on other sites
Elijah

That’s some welding but doable. Hope someone puts back on road

Share this post


Link to post
Share on other sites
kiran_182

Bbs ra 13" passable bit not mint £150 plus a set of gt steels and caps

 

Gt gearbox £80

 

Full mpi conversion £250

- loom / ecu

- inlet, injectors, isv, tb, airbox and afm

- rear fuel pump 

 

Front seats £120 driver top corner need seem stich together

 

Full arch kit with side strips and sill covers £160 

 

 

Share this post


Link to post
Share on other sites
Qwerty

Where abouts are you? How much you after for the whole thing?

Share this post


Link to post
Share on other sites
kiran_182
27 minutes ago, Qwerty said:

Where abouts are you? How much you after for the whole thing?

 

South coast, probably as far from you as possible 

Share this post


Link to post
Share on other sites
Qwerty
2 hours ago, kiran_182 said:

 

South coast, probably as far from you as possible 

Typical!

Share this post


Link to post
Share on other sites
kiran_182

Polo gt camshaft £75 posted

 

 

A rolling shell will be availible too, will leave steering damper arb rear beam suspension and brakes all in place all the pannels are good 

Edited by kiran_182

Share this post


Link to post
Share on other sites
Da_trip

Afternoon, do you have the outside trim for sale ? also looking for the center Console and switches ?

 

Share this post


Link to post
Share on other sites
schneil

Are you willing to split the engine conversion?  I'm looking for a GT air flow meter

 

Share this post


Link to post
Share on other sites
Sej

Hi interest in arches kit if still available.

and willing to post?

Share this post


Link to post
Share on other sites
mdgN

Interested in rear beam.

Share this post


Link to post
Share on other sites
kiran_182

This car has been sold whole, sorry 

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • steveo3002
      By steveo3002
      just posting this to document it really
       
      early mk2 round headlight 3f ecu made by bosch , part number ending J , see it has lots of surface mount parts , general better quality feel to it
       
      later mk2f 3f K made by ken?   less surface mount parts and these burnt /manually fitted  parts seem the norm as we opened up another and its the same , the J one is mint
       
       


    • kiran_182
      By kiran_182
      Abd 3f injection. 
       
      Start the car and runs fine for 3 or 4 min then idles low and cuts out, wont repond to throttle when chugging and ramind this way on restart unless left 
       
      Any ideas 
    • steveo3002
      By steveo3002
      my 3f conversion failed the mot today , 10% co
       
      at 10% its running fairly normal , sounds and drives "okay" 
       
      so i gets home and mess with the afm , i can get it lower towards a pass , but it just hates it a pops and bangs and really doesnt like it all
       
      all service parts new /good , o2 unplugged,temp sender looks good on scanner , tried another afm , messed with ign timing etc  checked all i can think off , cant really get my head round why it wants to run so rich and wont /struggles near normal readings 
    • steveo3002
      By steveo3002
      earlier this year ive fitted full 3f mpi injection to my previously refreshed abd , still not running 100% and i decided to re seal the inlet mani incase it was leaking 
       
      i gets it off and find the number 1 end is oily . not dripping but a good wet coating of clean engine oil 
       
      thing is all breathers are vented elsewhere so i dont really get where on earth it could have come from ?   
    • schneil
      By schneil
      Wanted - airflow meter for polo GT.
      Part numbers (030906301 867129611B 0280200048 Bosch D2721)
      It is the same part on a 1.3 Golf and Polo NZ.
      Cheers

Follow: #ClubPoloUK

The Polo Social

Volkswagen Polo Owners Club

×

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. Terms of Use Privacy Policy Guidelines